Hidden fasteners are clips that sit in a groove along each board’s edge and screw down into the joist, so the walking surface shows no screw heads and the clip sets the gap between boards. Face screws go straight through the top of the board; on composite they are color-matched or covered with a plug, and they are still the right choice for square-edge boards like the border boards around a deck’s edge and the treads on its steps. Most composite decks we build use clips across the field and face fastening at the edges. Our Ohio, Kentucky and Indiana deck materials pillar explains how fastening fits into choosing a board in the first place.
Fasteners rarely come up at the first meeting, but they shape how a finished deck looks from a lawn chair and how it behaves in a January cold snap. At Building Character we follow each board maker’s own fastening and spacing instructions, because the warranty depends on it and because composite boards move with temperature. Below we compare the two systems on looks, board movement, cost and future repairs, and show where each belongs on a typical deck.
Fasteners rarely come up at the first meeting, but they shape how a finished deck looks from a lawn chair and how it behaves in a January cold snap. At Building Character we follow each board maker’s own fastening and spacing instructions, because the warranty depends on it and because composite boards move with temperature. Below we compare the two systems on looks, board movement, cost and future repairs, and show where each belongs on a typical deck.
Quick answer
9 min read
Hidden clipsOne clip and screw at each joist, in the board’s groove
Face screwsThrough the top; color-matched or plugged on composite
TimberTech side gap1/8–3/16 in. between boards
Deckorators StealthLock gap1/4 in.
TimberTech butt joints at 32°F or below3/16 in. gap
Borders and stair treadsSquare-edge boards, face fastened
Cost effectMore hardware and labor for clips; shown as a line on the proposal
How each fastening system holds a board
A hidden clip grabs the grooved edges of two neighboring boards and is screwed down into the joist between them, while a face screw passes through the top of the board into the joist below. TimberTech’s CONCEALoc installation guide describes the clip method in plain terms: one fastener and one screw at each joist, with the screw driven at a 45-degree angle in the center of the joist. Each board ends up held at every joist without a single hole in its top face.
Face fastening is older and simpler. On wood decks it is the norm. On composite, the makers sell screws with heads tinted to the board color, or plug systems that set a cap of matching material over a counterbored screw. Trex’s picture-framing guide notes that grooved Trex boards are designed for its Hideaway clips, while border boards must be square-edge and are secured with Hideaway composite deck screws or Hideaway plugs.
Face fastening is older and simpler. On wood decks it is the norm. On composite, the makers sell screws with heads tinted to the board color, or plug systems that set a cap of matching material over a counterbored screw. Trex’s picture-framing guide notes that grooved Trex boards are designed for its Hideaway clips, while border boards must be square-edge and are secured with Hideaway composite deck screws or Hideaway plugs.
Grooved or square-edge: the board decides
Clips only work on boards milled with a side groove. A square-edge board has no groove, so it must be face fastened or held with an edge system the maker approves. That is why we choose the board profile and the fastening plan together: a deck with a wide border, wraparound stairs and a long fascia will have more square-edge pieces than a simple rectangle.
The look up close
Hidden clips give the cleanest surface, with nothing but the board grain and the gaps visible; colored face screws are hard to spot from standing height, and plugs disappear almost completely if they are set well. The difference is most noticeable on lighter boards and in low evening light, when screw heads can catch shadows.
Hidden clips, colored face screws and plugged screws compared
| Feature | Hidden clips | Colored face screws | Screw and plug |
|---|---|---|---|
| Top surface | No visible fasteners | Small colored heads in rows over each joist | Matching plugs, nearly invisible |
| Board edge needed | Grooved | Square-edge or grooved | Square-edge or grooved |
| Sets the gap | Yes, built into the clip | No, spacers set it | No, spacers set it |
| Typical use | Main field of the deck | Borders, stair treads, wood decks | Borders and stairs where looks matter most |
| Labor | More per board | Fastest | Most per fastener |
| Lifting one board later | Harder; clips hold both edges | Easiest | Plugs must be drilled out |
Deck resurfacing in progress with new composite boards on an existing frame and taped joists
Board movement through an Ohio year
Composite and PVC boards grow a little in heat and shrink in cold, and both fastening systems have to leave room for it, which is why makers publish their gaps by temperature. NOAA counts roughly 57 freezes and thaws per average Cincinnati year in its engineering weather data for the city, so a deck installed on a mild day has to cope with both August sun and January lows.
Side-to-side, clips do the spacing for you. TimberTech’s guide calls for a side gap of 1/8 to 3/16 inch and a minimum 3/16 inch where a board meets a house wall or post. Deckorators says its StealthLock clips for grooved boards hold 1/4 inch spacing to allow for natural expansion and contraction (Deckorators Voyage page, FAQ). End to end, the gap depends on the day you install, and TimberTech prints it as a chart.
Side-to-side, clips do the spacing for you. TimberTech’s guide calls for a side gap of 1/8 to 3/16 inch and a minimum 3/16 inch where a board meets a house wall or post. Deckorators says its StealthLock clips for grooved boards hold 1/4 inch spacing to allow for natural expansion and contraction (Deckorators Voyage page, FAQ). End to end, the gap depends on the day you install, and TimberTech prints it as a chart.
TimberTech composite butt-joint gaps by installation temperature, from its CONCEALoc guide
| Air temperature at install | Butt-joint gap |
|---|---|
| 32°F and below | 3/16 in. |
| 33–74°F | 1/8 in. |
| 75°F and above | 1/32 in. |
Cold-weather installs
The same TimberTech guide requires pre-drilling below 45°F to avoid end splitting and screw shear. A deck finished during a cold November week gets a different end gap and more pre-drilling than one finished in June. These are the maker’s rules, and following them is part of keeping the board warranty valid.
Talk it through with us
Send a few photos or book a visit and we’ll walk you through the options for your yard.
What changes on the price
Hidden fasteners add some hardware and labor compared with face screws, but on a typical composite deck the difference is a small line next to the board tier, the railing and the height. A clip goes in at every joist crossing, so a deck framed at 12 inches on center uses more clips than one at 16. Plugged screws take the most time per fastener because each hole is counterbored and capped.
We don’t publish a separate per-square-foot figure for fasteners, because it depends on the board, the joist spacing and how many square-edge pieces the design has. Your proposal shows it. For context, mid composite decking runs about $45–65 per square foot installed in our 2026 planning ranges and premium composite or PVC about $55–80, and those ranges already include standard fastening for the board line.
We don’t publish a separate per-square-foot figure for fasteners, because it depends on the board, the joist spacing and how many square-edge pieces the design has. Your proposal shows it. For context, mid composite decking runs about $45–65 per square foot installed in our 2026 planning ranges and premium composite or PVC about $55–80, and those ranges already include standard fastening for the board line.
- Joist spacing: tighter spacing means more clips
- Board profile: square-edge boards need face screws or plugs
- Border and stair count: more edges, more face fastening
- Plugs versus colored screws: plugs add time at every fastener
- Install season: cold days add pre-drilling
Hidden fastening on wood and hardwood decks
Pressure-treated pine and cedar decks are nearly always face screwed, because the boards are square-edge and wood moves more across its width as it wets and dries. Hardwoods such as ipe are the exception: we fasten them with stainless screws or with hidden clips, and many owners pick clips for a furniture-like surface. Every hardwood board is pre-drilled whichever way it is fastened, so labor runs higher than on softwood. If you are still deciding on species, our post comparing pressure-treated, cedar and ipe decking covers how each one wears.
Where each one goes on a typical deck
On most composite decks we clip the main field and face fasten the edges, so the part you walk on looks clean while the borders, stairs and fascia stay tight. A single deck usually ends up with three or four fastening methods, each chosen for the piece it holds.
- Main field boards: hidden clips in the groove
- First and last board against the house or rim: the maker's starter clip or edge bracket
- Picture-frame border: square-edge boards, colored screws or plugs
- Stair treads: face fastened for a solid feel on each step
- Fascia: the maker's fascia screws
- Wood decks: coated or stainless face screws; hardwood pre-drilled
Borders and the clip-free look
A border is where people sometimes expect to see clips and are surprised to see screws. Because border boards are square-edge, they are face fastened by design. Our explainer on picture-frame decks goes into the framing and fastening behind a border, and plugs are the usual answer when you want the border to look as clean as the field.
Wide brown composite deck surface framed by black aluminum railing with an open lawn beyond
Repairs, replacements and choosing a brand
Face-screwed boards are easier to lift out one at a time; clipped boards take more care because each clip also holds the neighboring board, so swapping one in the middle of a field takes longer. Single-board swaps are not an everyday job, so this rarely decides the question, but it is worth knowing if you have a hot tub, a grill zone or a spot where something heavy might get dropped.
Each brand sells its own clip family and approves it for its own boards, and the fastening system is part of what the board warranty assumes. We use the clips the maker specifies. TimberTech, AZEK and Deckorators have all certified us as an installer; we install Trex and Fiberon too, without that certification. Our TimberTech decking page shows the composite and Advanced PVC lines that pair with CONCEALoc and TimberTech’s other systems.
We plan the fastening on every deck we design, whether it is going up in Boone County or on the Ohio side, and it shows up in your free 3D design as a clean field with a defined edge. If you have a strong preference for no visible screws anywhere, tell us early, because it affects the board profile and the border design.
Each brand sells its own clip family and approves it for its own boards, and the fastening system is part of what the board warranty assumes. We use the clips the maker specifies. TimberTech, AZEK and Deckorators have all certified us as an installer; we install Trex and Fiberon too, without that certification. Our TimberTech decking page shows the composite and Advanced PVC lines that pair with CONCEALoc and TimberTech’s other systems.
We plan the fastening on every deck we design, whether it is going up in Boone County or on the Ohio side, and it shows up in your free 3D design as a clean field with a defined edge. If you have a strong preference for no visible screws anywhere, tell us early, because it affects the board profile and the border design.
Related reading
What Is a Picture-Frame Deck? Borders, Blocking and Cost
From our guide: Deck Materials Guide for Ohio, Kentucky and Indiana Weather.
Deck Board Patterns: Herringbone, Diagonal, Inlays and Cost
From our guide: Deck Materials Guide for Ohio, Kentucky and Indiana Weather.
Best Composite Decking for Ohio Winters: What Holds Up
From our guide: Deck Materials Guide for Ohio, Kentucky and Indiana Weather.
Hidden deck fastener questions
Are hidden deck fasteners worth it?
For most composite decks, yes. Clips give a surface with no screw heads and set the board gap automatically. The extra cost is modest next to the board tier and railing, and we still face fasten borders and stairs where square-edge boards are used.
Do hidden fasteners hold up in Cincinnati winters?
They do when they are installed to the maker’s rules. NOAA’s figure for Cincinnati is 57 freeze-thaw cycles in an average year, which is why we set end gaps for the install temperature and pre-drill on cold days, as TimberTech’s guide requires below 45°F.
Can I use face screws on composite decking?
Yes, with the screws the board maker approves. Colored composite screws and plug systems are designed for it, and they are standard on border boards, stair treads and square-edge boards that have no groove for a clip.
Do hidden fasteners cost more?
Usually a little, because clips go in at every joist and take more labor per board. We don’t price fasteners as a separate per-square-foot rate; the proposal for your deck includes the fastening plan and its cost.
What fasteners do you use on decks in Northern Kentucky and Ohio?
The same across the tri-state: each board maker’s own clips and screws, installed to its gapping and spacing rules. On wood decks we use coated or stainless face screws, and hardwoods are pre-drilled.
Sources
TimberTech: installing composite decking with CONCEALoc hidden clip fasteners (gapping and temperature chart)
Trex: how to picture frame a deck (grooved boards, Hideaway clips, screws and plugs)
Deckorators: Voyage decking FAQ (StealthLock clips and 1/4 in. spacing)
NOAA NCEI Engineering Weather Data: Cincinnati, OH (average annual freeze-thaw cycles)
Trex: how to picture frame a deck (grooved boards, Hideaway clips, screws and plugs)
Deckorators: Voyage decking FAQ (StealthLock clips and 1/4 in. spacing)
NOAA NCEI Engineering Weather Data: Cincinnati, OH (average annual freeze-thaw cycles)